Hello, reading the fault code 1215, which means that the air flow meter or its line is poor. After testing, the impedance of the air flowmeter does not meet the requirements. After replacing the air flowmeter, the condition of the car improved slightly, but the fault was still there. Check again and find that the 4th cylinder spark plug is covered with gasoline, indicating that the cylinder is not working.
The engine has serious carbon accumulation. The most common cause of idling jitter is excessive carbonisation of the throttle valve or fuel nozzle.
The solutions to unstable idle speed, shaking, shaking and black smoke are as follows: the engine is seriously carbonized. The common cause of car shaking is that the throttle valve is too dirty or the fuel nozzle has too much carbon.Solution: Clean the oil road and check whether there is carbon in the idle motor, which should be cleaned.
The control unit receives the wrong signal and sends the wrong instruction, causing the engine idling intake control to be inaccurate, causing the engine to burn abnormally, which is an indirect cause of unstable idle speed. Common causes are: air flow meter or its line failure; intake pressure sensor or its line failure; engine control unit plug due to poor contact with water inlet or internal computer failure.
Engine ignition order is 2; that is to say, when cylinder 1 is doing work, cylinder 3 is in a compressed state, cylinder 4 is in the intake state, and cylinder 2 is in the exhaust state. Status.
People sit in the cab, and the order of the cylinder is: 5 on the right, and 6 on the left.In this case, the ignition order is: 1-4-5-2-3-6.
The ignition order of the engine is 2; that is, when the 1st cylinder is in the "work", the 3rd cylinder is in the "compression" state, the 4th cylinder is in the "ink-ink" state, and the 2nd cylinder is in the "exhaust" state. Depending on the number of engine cylinders, the ignition order of the engine will also vary.
Engine carbon accumulation problem, the engine will accumulate some carbon accumulation after a period of use, which will cause engine damage, difficulty in starting, poor acceleration, starting The machine is too noisy and other phenomena. Mixed gas combustion is poor and gas combustion is insufficient. Sensor problem. Multiple sensors are aging. If the owner does not add oil as required, it will lead to accelerated engine wear and abnormal operation in the long run, and the engine fault light will turn on. Generally, replacing the oil with the corresponding conditions can eliminate the fault light. The reasons why the engine fault light is on are engine carbonisation problems, poor combustion of mixed gas, sensor problems, maintenance problems and oil quality problems.Car owners need to regularly clean the carbon accumulation of the engine, check the working condition of the sensor, maintain it regularly, and use qualified oil products. The fuel quality is poor and does not meet the standard.
Germany international trade insights-APP, download it now, new users will receive a novice gift pack.
Hello, reading the fault code 1215, which means that the air flow meter or its line is poor. After testing, the impedance of the air flowmeter does not meet the requirements. After replacing the air flowmeter, the condition of the car improved slightly, but the fault was still there. Check again and find that the 4th cylinder spark plug is covered with gasoline, indicating that the cylinder is not working.
The engine has serious carbon accumulation. The most common cause of idling jitter is excessive carbonisation of the throttle valve or fuel nozzle.
The solutions to unstable idle speed, shaking, shaking and black smoke are as follows: the engine is seriously carbonized. The common cause of car shaking is that the throttle valve is too dirty or the fuel nozzle has too much carbon.Solution: Clean the oil road and check whether there is carbon in the idle motor, which should be cleaned.
The control unit receives the wrong signal and sends the wrong instruction, causing the engine idling intake control to be inaccurate, causing the engine to burn abnormally, which is an indirect cause of unstable idle speed. Common causes are: air flow meter or its line failure; intake pressure sensor or its line failure; engine control unit plug due to poor contact with water inlet or internal computer failure.
Engine ignition order is 2; that is to say, when cylinder 1 is doing work, cylinder 3 is in a compressed state, cylinder 4 is in the intake state, and cylinder 2 is in the exhaust state. Status.
People sit in the cab, and the order of the cylinder is: 5 on the right, and 6 on the left.In this case, the ignition order is: 1-4-5-2-3-6.
The ignition order of the engine is 2; that is, when the 1st cylinder is in the "work", the 3rd cylinder is in the "compression" state, the 4th cylinder is in the "ink-ink" state, and the 2nd cylinder is in the "exhaust" state. Depending on the number of engine cylinders, the ignition order of the engine will also vary.
Engine carbon accumulation problem, the engine will accumulate some carbon accumulation after a period of use, which will cause engine damage, difficulty in starting, poor acceleration, starting The machine is too noisy and other phenomena. Mixed gas combustion is poor and gas combustion is insufficient. Sensor problem. Multiple sensors are aging. If the owner does not add oil as required, it will lead to accelerated engine wear and abnormal operation in the long run, and the engine fault light will turn on. Generally, replacing the oil with the corresponding conditions can eliminate the fault light. The reasons why the engine fault light is on are engine carbonisation problems, poor combustion of mixed gas, sensor problems, maintenance problems and oil quality problems.Car owners need to regularly clean the carbon accumulation of the engine, check the working condition of the sensor, maintain it regularly, and use qualified oil products. The fuel quality is poor and does not meet the standard.
How to scale export operations with data
author: 2024-12-24 09:32HS code-based freight consolidation
author: 2024-12-24 07:39Trade compliance training resources
author: 2024-12-24 06:53HS code-driven freight route adjustments
author: 2024-12-24 08:53HS code-based competitive advantage analysis
author: 2024-12-24 08:19China trade data analysis tools
author: 2024-12-24 08:15Trade data for enterprise resource planning
author: 2024-12-24 07:46Customs authorization via HS code checks
author: 2024-12-24 07:19759.96MB
Check447.16MB
Check293.84MB
Check468.11MB
Check875.12MB
Check667.74MB
Check429.91MB
Check164.95MB
Check731.76MB
Check315.49MB
Check165.52MB
Check914.64MB
Check951.35MB
Check575.86MB
Check375.81MB
Check845.33MB
Check237.68MB
Check119.52MB
Check123.15MB
Check198.18MB
Check542.86MB
Check691.17MB
Check184.74MB
Check663.59MB
Check785.98MB
Check461.48MB
Check348.75MB
Check656.76MB
Check599.59MB
Check679.34MB
Check796.15MB
Check992.95MB
Check988.82MB
Check172.31MB
Check418.12MB
Check275.63MB
CheckScan to install
Germany international trade insights to discover more
Netizen comments More
1485 Global trade compliance playbooks
2024-12-24 09:09 recommend
1106 HS code-based container stowage planning
2024-12-24 09:05 recommend
2876 Trade data-driven investment strategies
2024-12-24 08:08 recommend
1084 Cocoa and chocolate HS code insights
2024-12-24 07:41 recommend
2124 HS code-based predictive analytics
2024-12-24 07:32 recommend